Which Fuel Line Is The Return Line?

Which fuel line is the return line?

Does fuel line with filter go to primer bulb?

For this 2-stroke engine carburetor design, the primer bulb is built on top of the assembly. The bulb pulls fuel through the filtered fuel line and into the carburetor and then it also pushes it out of the carburetor and out the unfiltered return line.

How do you connect a primer bulb?

What does the fuel line connect to?

Fuel hoses comes in many different locations on vehicles. On older vehicles, there are steel lines from the fuel tank to the carburetor or injectors of a fuel system. Some of the older vehicles have short fuel hoses that connect the steel line to the fuel pump, fuel tank, and carburetor.

What size fuel return line should I use?

The Fuel Return Line should be at least the same size, or one size larger than the supply. Make sure there are no sharp bends or kinks. The return line should direct fuel close to the bottom of the tank and away from the pickup.


Related guide for Which Fuel Line Is The Return Line?


Which way does a primer bulb go?


Where does a primer bulb go?

ANSWER: The primer bulb, which is located in the fuel line between the gas tank and the engine, is used to fill the carburetor with fuel when the engine is started cold. The rubber bulb resembles an oblong ball. Inside the bulb are two valves that open and close.


How do you connect fuel lines?


Are primer bulbs one way?

1. Frequently used as a hand pump in boats for fuel supply to the out-board engine. Hand bulb primer to suit petrol of comes with a one way valve installed to help quickly prime the fuel system.


What type of fuel line should I use?

The best fuel line material depends on your needs. However, the best material for fuel lines is polytetrafluoroethylene or PTFE. PTFE fuel line is made of plastic material specifically known as Teflon. This fuel line material is impervious is resistant to the degenerative fuel effects which could form vapor barriers.


What lines or pipes connect the engine to the fuel tank?

The fuel line typically consists of rigid metal pipes, with flexible rubber or plastic hoses running from the pipes to the tank and the fuel pump , and from the pump to the carburettor .


Where does the fuel line go?

The (clear) main fuel line with the filter (filter inside the fuel tank) goes to the bottom of the carburetor (or the elbow shaped nipple). The (clear) fuel intake line runs from the top of the carburetor (straight nipple) and goes to the short post on the back of the primer bulb.


Can a fuel return line be too big?

The return line has to flow enough not to create a back pressure on the regulator. This will effect fuel flow and pressure on the rail side. You cannot go to big.


How do I know what size fuel line I have?

How is fuel line size measured? Place the top of a 1/4-inch wrench with an open end over the fuel line. Slide it carefully over the line so that it fits snugly against the tubing. Read the wrench's measurements to determine the diameter of the fuel line.


Is a return fuel line necessary?

You don't need it with a mechanical pump. Mechanical pumps supply fuel based on RPM, and so long as you're not running a big hipo mechanical pump, you're fine without a return.


Why am I not getting gas in my primer bulb?

When the primer bulb isn't working, it may be a problem with the bulb itself, with the fuel lines that feed fuel to the bulb or both. The same goes for fuel lines. When they've hardened and cracked, they let in air, which makes it impossible to draw the fuel into the carburetor properly.


How does a fuel line primer bulb work?

  • Primer bulb is pressed and released.
  • When released a vacuum is created and fresh fuel is drawn into the intake fuel line.
  • The intake fuel line deposits fuel into the carburetor making it ready or “primed” for combustion.

  • How do you put fuel lines on a Weedeater?


    Does a primer bulb have to be vertical?

    In the ideal world, you should keep the bulb in that vertical position all the time. Most of the time, it can not be accomplished easily. The next best position for running the engine, then, will be laying horizontal, after you squeeze the bulb, holding it vertical.


    How do you keep a carburetor primed?

  • Crank the car for about 15 seconds.
  • Stop for about 15 seconds.
  • Pump the accelerator petal twice.
  • Crank the car again, if it doesn't start immediately keep cranking the car for a maximum of 15 seconds.

  • How do you quick connect fuel lines?


    How does a primer work on a 2 stroke engine?


    Are Stihl primer bulbs universal?

    Chainsaw , strimmer , brushcutter and hedgecutter primer bulbs for . Primer bulbs fit many Zama, Walbro, Shindaiwa, Stihl and Homelite carburetors Fits all 2-cycle and 4-cycle Zama carburetors (#0057004) Fits Walbro models WA, WT, WY, WYJ, WYK, WYL, WYP & WZ carburetors that require a .


    How do you change a primer bulb on a Craftsman chainsaw?


    Was this post helpful?

    Leave a Reply

    Your email address will not be published.